Thema: Pingulux Plus bootet nicht mehr

Zitat von Lizard

Das Image sieht Korrupt aus, Bootloader dürfte i.O. sein, bootet ja durch, STB-ID 09 00 08 00 ... ist korrekt für Pingulux und Pingulux Plus.

OK und was heißt das, bzw. wie kann ich das fixen? Mit dem Help Pack, das kükenlos gepostet hat?

Bootloader (Uboot) ist in Ordnung.
Ist ja schon mal was.
Image defekt, daher wohl nochmal frisch laden (eventuell mit anderen PC). Entpacken (eventuell mit anderen Entpacker) um halt Fehler auszuschließen.
Neu installieren via USB. Wenn das nicht klappt, dann via tftp probieren.

Vielleicht liegts wirklich einfach am Packprogramm, das wäre die eleganteste Möglichkeit.

Ach so, wenn du schon dabei bist, kannst natürlich auch NFR testen.

Hoffentlich klappts noch

Zitat von kükenlos

Bootloader (Uboot) ist in Ordnung.
Ist ja schon mal was.
Image defekt, daher wohl nochmal frisch laden (eventuell mit anderen PC). Entpacken (eventuell mit anderen Entpacker) um halt Fehler auszuschließen.
Neu installieren via USB. Wenn das nicht klappt, dann via tftp probieren.

Vielleicht liegts wirklich einfach am Packprogramm, das wäre die eleganteste Möglichkeit.

Ach so, wenn du schon dabei bist, kannst natürlich auch NFR testen.

Hoffentlich klappts noch

Mit einem anderen Programm entpacken bringt schon mal nichts. Muss ich morgen nochmal mit einem anderen PC probieren.
Echt seltsam das Ganze. Vielleicht liegts an Windows 10.
Danke schon mal, probier das ganze morgen nochmal. Vielleicht hat bis dahin noch jemand eine Idee

Hallo,

ich habe jetzt nochmal durchprobiert und bin zu einem kleinen Erfolg gekommen. Nachdem ich das NFR-image geflasht habe, hing der Receiver wie bei dem Open-ATV Image bei 49% mit selbigem Log.
Doch plötzlich lief das Image weiter und hat gebootet. .
Als ich dann einen Sendersuchlauf starten wollte, kam die Ernüchterung. Kein Bild mehr und Image scheint sich wieder aufgehängt zu haben.
Vielleicht doch ein Hardwarefehler am Tuner?
Vielleicht doch ein Problem mit den Bootargs? Weil mir ist heute aufgefallen, dass beim Wechsel zwischen Spark und Enigma über die FP-Tasten nicht "spark" angezeigt wird, sondern weiter "fact". Das Laden von Spark funktioniert zwar, aber das ist doch auch seltsam. Bei E2 ist alles in Ordnung.

Hier mal der Log vom Start von NFR
Übrigens glaube ich nicht, dass es an der stb-id liegt, wenn ihr mal relativ oben im Log unter Ident schaut, steht die 09 00 08 00.

Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD




U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel


DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 44 25
Hit ESC to stop autoboot: 0


Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
Image Name: Linux-2.6.32.61_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2364482 Bytes = 2.3 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.61_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2364482 Bytes = 2.3 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 908004425


Starting kernel console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 rw ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:LINUX7109:eth0:off bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 nwhwconf=device:eth0,hwaddr:24:00:08:00:44:25 Manufacture=Spark-Project STB_ID=09:00:08:00:00:44:25 - 0x00000000 - 0 ...


Linux version 2.6.32.61_stm24_0217 (nfr@nfr-Aspire-E5-574) (gcc version 4.8.4 20141219 (GCC) ) #1 PREEMPT Tue May 31 00:24:55 CEST 2016
Boot params:
... MOUNT_ROOT_RDONLY - 00000001
... RAMDISK_FLAGS - 00000000
... ORIG_ROOT_DEV - 00000200
... LOADER_TYPE - 00000000
... INITRD_START - 00000000
... INITRD_SIZE - 00000000
Booting machvec: sat7111
Node 0: start_pfn = 0x40000, low = 0x50000
Zone PFN ranges:
Normal 0x00040000 -> 0x00050000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00040000 -> 0x00050000
Spark-7111 board initialization
STx7111 version 3.x
bpa2: partition 'bigphysarea' created at 0x48000000, size 32768 kB (0x02000000 B)
bpa2: partition 'LMI_IO' created at 0x4a000000, size 98304 kB (0x06000000 B)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 rw ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:LINUX7109:eth0:off bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 nwhwconf=device:eth0,hwaddr:24:00:08:00:44:25 Manufacture=Spark-Project STB_ID=09:00:08:00:00:44:25
bpa2: partition 'bigphysarea' created at 0x40e0d000, size 24000 kB (0x01770000 B)
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
PVR=04909200 CVR=60880000 PRR=00009a10
I-cache : n_ways=2 n_sets=512 way_incr=16384
I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Memory: 92416k/262144k available (2986k kernel code, 898k data, 116k init)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:600
Failed to enable clk CLKA_PLL0LS, ignoring
console [ttyAS0] enabled
sh_tmu: TMU0 used for clock events
sh_tmu: TMU0 used for periodic clock events
sh_tmu: TMU1 used as clock source
Calibrating delay loop... 448.51 BogoMIPS (lpj=897024)
Mount-cache hash table entries: 512
CPU: STx7111
devtmpfs: initialized
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
DMA: Registering DMA API.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource TMU1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
sq: Registering store queue API.
Installing knfsd (copyright (C) 1996 Link nur für registrierte und freigeschaltete Mitglieder sichtbar. ).
Slow work thread pool: Starting up
Slow work thread pool: Ready
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
JFS: nTxBlock = 722, nTxLock = 5781
msgmni has been set to 180
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
lirc_dev: IR Remote Control driver registered, major 61
lirc-stm: probe found data for platform device lirc-stm
lirc-stm: STM LIRC plugin using IRQ 125 in IR mode
lirc_dev: lirc_register_driver: sample_rate: 0
STMicroelectronics LIRC driver initialized.
STMicroelectronics ASC driver initialized
stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc
loop: module loaded
physmap platform flash device: 00800000 at 00000000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 3 MTD partitions on "physmap-flash":
0x000000000000-0x000000080000 : "Boot firmware"
0x000000080000-0x000000780000 : "Kernel"
0x000000780000-0x000000800000 : "Reserve"
ONFI flash detected
No valid ONFI param page found (bad CRC)
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
stm-nand-emi: Using legacy platform timing data
stm-nand-emi: Configuring EMI Bank 1 for NAND access
cmdlinepart partition parsing not available
Creating 4 MTD partitions on "stm-nand-emi.0":
0x000000000000-0x000000800000 : "Spark Kernel"
0x000000800000-0x000018000000 : "Spark Rootfs"
0x000018000000-0x000018800000 : "kernel"
0x000018800000-0x00001ff00000 : "rootfs"
stmmac - user ID: 0x10, Synopsys ID: 0x33
No HW DMA feature register supported
Enhanced/Alternate descriptors
RX Checksum Offload Engine supported
TX Checksum insertion supported
Wake-Up On Lan supported
STMMAC MII Bus: probed
eth0: PHY ID 00000000 at 0 IRQ 0 (0:00)
eth0: PHY ID 0007c0f1 at 1 IRQ 0 (0:01) active
eth0: PHY ID 00000000 at 2 IRQ 0 (0:02)
eth0: PHY ID 00000000 at 3 IRQ 0 (0:03)
eth0: PHY ID 00000000 at 4 IRQ 0 (0:04)
eth0: PHY ID 00000000 at 5 IRQ 0 (0:05)
eth0: PHY ID 00000000 at 6 IRQ 0 (0:06)
eth0: PHY ID 00000000 at 7 IRQ 0 (0:07)
eth0: PHY ID 00000000 at 8 IRQ 0 (0:08)
eth0: PHY ID 00000000 at 9 IRQ 0 (0:09)
eth0: PHY ID 00000000 at 10 IRQ 0 (0:0a)
eth0: PHY ID 00000000 at 11 IRQ 0 (0:0b)
eth0: PHY ID 00000000 at 12 IRQ 0 (0:0c)
eth0: PHY ID 00000000 at 13 IRQ 0 (0:0d)
eth0: PHY ID 00000000 at 14 IRQ 0 (0:0e)
eth0: PHY ID 00000000 at 15 IRQ 0 (0:0f)
eth0: PHY ID 00000000 at 16 IRQ 0 (0:10)
eth0: PHY ID 00000000 at 17 IRQ 0 (0:11)
eth0: PHY ID 00000000 at 18 IRQ 0 (0:12)
eth0: PHY ID 00000000 at 19 IRQ 0 (0:13)
eth0: PHY ID 00000000 at 20 IRQ 0 (0:14)
eth0: PHY ID 00000000 at 21 IRQ 0 (0:15)
eth0: PHY ID 00000000 at 22 IRQ 0 (0:16)
eth0: PHY ID 00000000 at 23 IRQ 0 (0:17)
eth0: PHY ID 00000000 at 24 IRQ 0 (0:18)
eth0: PHY ID 00000000 at 25 IRQ 0 (0:19)
eth0: PHY ID 00000000 at 26 IRQ 0 (0:1a)
eth0: PHY ID 00000000 at 27 IRQ 0 (0:1b)
eth0: PHY ID 00000000 at 28 IRQ 0 (0:1c)
eth0: PHY ID 00000000 at 29 IRQ 0 (0:1d)
eth0: PHY ID 00000000 at 30 IRQ 0 (0:1e)
eth0: PHY ID 00000000 at 31 IRQ 0 (0:1f)
nwhw_config: (eth0) setting mac address: 24:00:08:00:44:25
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
Linux video capture interface: v2.00
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st231.0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa0000000 size 0x00400000
cop. addr 0x40000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231.1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa0400000 size 0x00400000
cop. addr 0x40400000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
DMA: Registering fdma_dmac.0 handler (16 channels).
IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.0: firmware: using built-in firmware fdma_STx7111_0.elf
DMA: Registering fdma_dmac.1 handler (16 channels).
IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.1: firmware: using built-in firmware fdma_STx7111_1.elf
platform fdma_dmac.1: SLIM hw 0.0, FDMA fw 2.5
platform fdma_dmac.0: SLIM hw 0.0, FDMA fw 2.1
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
#0: STMicroelectronics STx7111 cut 3.x SOC audio subsystem
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
usb 1-1: new high speed USB device using stm-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
eth0: device MAC address 24:00:08:00:44:25
No MAC Management Counters available
IP-Config: Complete:
device=eth0, addr=172.100.100.249, mask=255.255.0.0, gw=172.100.100.174,
host=LINUX7109, domain=, nis-domain=(none),
bootserver=172.100.100.174, rootserver=172.100.100.174, rootpath=
scsi 0:0:0:0: Direct-Access flash disk 5.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 1992192 512-byte logical blocks: (1.02 GB/972 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
VFS: Mounted root (jffs2 filesystem) on device 31:6.
devtmpfs: mounted
Freeing unused kernel memory: 116k freed
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x40000000
seeking to 0
seeking to 60980
seeking to 148478
seeking to 1484b0
seeking to 1484e8
seeking to 158858
seeking to 158864
seeking to 158880
seeking to 184d94
seeking to 186e00
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x40400000
seeking to 0
seeking to 5e00
seeking to 12460
seeking to 1ab60
seeking to 154300
seeking to 154338
seeking to 154370
seeking to 191a58
seeking to 191a60
seeking to 191a68
seeking to 191a70
seeking to 1aae40
seeking to 1aaf00
INIT: version 2.88 booting
mkdir: can't create directory '/tmp': No such file or directory
mkdir: can't create directory '/tmp': No such file or directory
find: /media/hdd: No such file or directory
rmdir: '/media/hdd': No such file or directory
stmcore-display: using HDMI hotplug
stmcore-display: STi7111 display probed
device probe found 2 display pipelines
requesting frm: 'component.fw', c11c2378/8740c850
stm-awg: firmware: requesting component.fw
frm 'component.fw' successfully loaded
requesting frm: 'fdvo0.fw', c11c2378/8740ce50
stm-awg: firmware: requesting fdvo0.fw
loading frm: 'fdvo0.fw' failed: -2
[CEC] init - starting
[CEC] The above error is a wanted behaviour as this was a ping!
Fulan front panel driver
VfdType = 2
CpuType = 2
DisplayInfo = 1
scankeyNum = 8
swMajorVersion = 1
swSubVersion = 10
stby key 0 = 9966da25
stby key 1 = 11eeda25
stby key 2 = 1ce37887
stby key 3 = c43b7887
stby key 4 = dd227887
blue key 0 = 996640bf
blue key 1 = 11ee40bf
blue key 2 = 1ce352ad
blue key 3 = c43b52ad
blue key 4 = dd2228d7
input: fulan front panel buttons as /devices/virtual/input/input0
aotom-rtc aotom-rtc: rtc core: registered aotom as rtc0
stmfb: fb0 parameters = "1280x720-32@50:15m:pal:yuv:yuv"
stmfb: Starting HDMI Output hdmi = 875b0000
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: EDID Read Error, setup safe EDID
stmfb: Setting Safe EDID
stmfb: fb1 parameters = "<NULL>"
Init of MME log wrapper
stm_v4l2_register_driver: driver 'stmvout' registered
stm_v4l2_register_driver: driver 'stmvbi' registered
snd_pseudo snd_pseudo.0: firmware: requesting downmix.fw
pseudocard: 1 pseudo soundcard(s) found
stv090x loaded
pti: module license 'NO' taints kernel.
Disabling lock debugging due to kernel taint
pti loaded (videoMem = 4096, waitMS = 20, enableStatistic = 0)
no swts ->routing streams from dvr0 direct to the player
DVB: registering new adapter (STM Streamer)
0: DeviceContext 87cbe088, DvbDemux 87cbe4c4, DmxDevice 87cbe6ac
CaInit()
Initializing CI Controller
ptiInit context = 87cbe088, demux = 87cbe4c4
[Spark] Init Stream Routing...
Load real TC Code
TC_Data = fe238000, TC_Code = fe23c000
Readback TC ... successfull
using videoMem = 770048 (packets = 4096)
pti: pti_buffer_pool_init: allocate 188 pages (770048 bytes)
DMA(0) base = 49380000, top = 4943c000, buffer = 49380000, size 770048
freeBuffer(): free = 1
stv090x_register_frontend: stv090x DVB: 0.11
pti_task: using 1 dma channel
tuner = 1
stv090x_register_frontend: init tuner 0
> (bus = 3) init_stv090x_device
i2c adapter = 0x87e4e418
i2c addr = 68
tuner enable = 0.0
frontend_init >
[stv090x_attach]i2c adapter = 87e4e418
i2c addr=104
ix7306_write ucIOBuffer 4 Err = 0
ix7306_write ucIOBuffer 1 Err = 0
ix7306_write ucIOBuffer Err 2 = 0
ix7306_read Err = 0 ucData = 0x18
========tuner_sharp7306_identify =====
tuner_Sharp7306 is Identified
frontend_init: attached
ix7306_attach: Attaching Sharp BS2S7HZ7306A IX7306 8PSK/QPSK tuner
frontend_init: IX7306 attached
init_stv090x_device: Call dvb_register_frontend (adapter = 0x87cbe03c)
DVB: registering adapter 0 frontend 0 (STV090x Multistandard)...
stv090x_register_frontend: <
Free session: 0
Using session 0
Descrambler Handler = 40000
install_e2_procs(): entry already in use 'progress'
install_e2_procs(): entry already in use 'stb/fp/was_timer_wakeup'
1: DeviceContext 87cbe748, DvbDemux 87cbeb84, DmxDevice 87cbed6c
CaInit()
ptiInit context = 87cbe748, demux = 87cbeb84
Free session: 1
Using session 1
Descrambler Handler = 41000
2: DeviceContext 87cbee08, DvbDemux 87cbf244, DmxDevice 87cbf42c
CaInit()
ptiInit context = 87cbee08, demux = 87cbf244
convert_source(): invalid frontend source (2)
Free session: 2
Using session 2
Descrambler Handler = 42000
3: DeviceContext 87cbf4c8, DvbDemux 87cbf904, DmxDevice 87cbfaec
ptiInit context = 87cbf4c8, demux = 87cbf904
convert_source(): invalid frontend source (3)
Descrambler Handler = -2
stm_v4l2_register_driver: driver 'Linux DVB Overlay' registered
OSDEV_LinkDevice - /dev/allocator, Major 245, Minor 0
AllocatorLoadModule : Allocator device loaded
OSDEV_LinkDevice - /dev/h264pp, Major 246, Minor 0
H264ppLoadModule : H264pp device loaded
(bpamem_init): BPAMem driver register result = 0
Registering device 'sc', major '169'
Version of smartcard driver: [1.0.1]
ramzswap: disk size not provided. You can use disksize_kb module param to specify size.
Using default: (25% of RAM).
ramzswap: disk size set to 23152 kB
ramzswap: Initialization done!
Adding 23148k swap on /dev/ramzswap0. Priority:-1 extents:1 across:23148k SS
mkdir: can't create directory '/tmp': No such file or directory
LinuxDvb:DvbPlaybackCreate: Playback 874f89a0
mkdir: can't create directory '/tmp': No such file or directory
LinuxDvb:DvbPlaybackDelete: Playback 874f89a0, Usage = 0
ALSA: Restoring mixer settings...
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.min_free_kbytes = 8192
vm.dirty_ratio = 60
vm.swappiness = 30
No state is present for card STx7111
Found hardware: "STx7111" "" "" "" ""
Hardware is initialized using a generic method
Simple mixer control 'Analog',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Simple mixer control 'HDMI',0
Simple mixer control 'SPDIF',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 7 [61%] [on]
Mono: Playback 7 [61%] [on]
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 7 [61%] [on]
No state is present for card STx7111
No state is present for card MIXER0
Found hardware: "Pseudo Mixer" "Pseudo Mixer" "" "" ""
Hardware is initialized using a generic method
No state is present for card MIXER0
INIT: Entering runlevel: 3
Configuring network interfaces... ip: RTNETLINK answers: File exists
udhcpc (v1.24.1) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
Starting system message bus: dbus.
Starting Dropbear SSH server: dropbear.
Starting automount: automount: program is already running.
done.
Starting rpcbind daemon...done.
starting 8 nfsd kernel threads: done
starting mountd: done
Mounting remote filesystems...
creating NFS state directory: done
starting statd: done
starting Busybox Periodic Command Scheduler: crond... done.
crond[1086]: crond (busybox 1.24.1) started, log level 8


Fuse filesystem already available.
Mounting fuse control filesystem.
Starting internet superserver: inetd.
Starting lirc daemon: lircdinput: remote control as /devices/virtual/input/input1
lircd: Repeat rate set to delay: 700 period: 100
.
Starting syslogd/klogd: done
Starting telnet server: telnetd.
* starting FTP Server: vsftpd... done.
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
...done.
LinuxDvb:DvbPlaybackCreate: Playback 861e2c80
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.min_free_kbytes = 8192
vm.dirty_ratio = 60
vm.swappiness = 30
LinuxDvb:DvbPlaybackDelete: Playback 861e2c80, Usage = 0
enigma2 is the main pvr application... adjust oom score!
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 1
framebuffer not availablVFD/AOTOM: unknown IOCTL 0x1015
e.
stmhdmiio_get_cec_address - 875b0000
proc_tsmux_input0_write 1 A
proc_tsmux_input1_write 1 B
msg.addr = 96
config->addr = 96
ix7306_write: write error, err=-121
nim_vz7306_control: I2C write error init_data1
executing main
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
proc_denc_0_wss_write 4 - auto
Can't set policy, VideoStream NULL
proc_hdmi_edid_handling_read
stmhdmiio_get_edid_handling - 875b0000
proc_hdmi_edid_handling_read - 1
proc_hdmi_edid_handling_read
stmhdmiio_get_edid_handling - 875b0000
proc_hdmi_edid_handling_read - 1
proc_hdmi_edid_handling_read
stmhdmiio_get_edid_handling - 875b0000
proc_hdmi_edid_handling_read - 1
proc_hdmi_edid_handling_write 8 - [HDMI] EDID handling arg: 00000001
[HDMI] EDID handling: none strict
stmhdmiio_set_edid_handling - 875b0000
proc_hdmi_audio_source_read
stmhdmiio_get_audio_source - 875b0000
proc_hdmi_audio_source_read - 0
proc_hdmi_audio_source_read
stmhdmiio_get_audio_source - 875b0000
proc_hdmi_audio_source_read - 0
proc_hdmi_audio_source_read
stmhdmiio_get_audio_source - 875b0000
proc_hdmi_audio_source_read - 0
proc_hdmi_audio_source_write 3 - pcm
stmhdmiio_set_audio_source - 875b0000
Found mode to set 1080i50 at 19
stmfb: Starting HDMI Output hdmi = 875b0000
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
Found mode to set 1080i50 at 19
Found mode to set 1080i50 at 19
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: EDID Read Error, setup safe EDID
stmfb: Setting Safe EDID
stmfb: Starting HDMI Output hdmi = 875b0000
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: first EDID byte (255) is corrupt, attempting to fix..
stmfb: Invalid extension header checksum block0
stmfb: EDID Read Error, setup safe EDID
stmfb: Setting Safe EDID
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
ERROR:LinuxDvb:DvbDisplayDelete: Failed to close audio surface
ERROR:LinuxDvb:DvbDisplayDelete: Failed to close audio surface
aotom_write_rtc_offset 4 - aotom_write_rtc_offset -> 3600
offset: 3600
aotom_write_rtc 13 - aotom_write_rtc -> 946684916.739
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
failed to get output window -22
failed to set output window -22
pti_hal_set_source(): invalid session (fffffffd)

Hier auch nochmal meine Bootargs

bootdelay=3
baudrate=115200
board=mb618
monitor_base=0xA0000000
monitor_len=0x00080000
monitor_sec=0xa0000000 0xa007ffff
load_addr=0x80000000
unprot=protect off $monitor_sec
update=protect off $monitor_sec;erase $monitor_sec;cp.b $load_addr $monitor_base $monitor_len;protect on $monitor_sec
HOSTNAME=LINUX7109
ethaddr=00:80:E1:12:06:38
ipaddr=192.168.40.63
netmask=255.255.255.0
gatewayip=192.168.3.1
serverip=192.168.40.19
kernel_base_spark= 0xa0080000
kernel_base_enigma2=0x18000000
kernel_sec= a0080000 a077ffff
kernel_len= 0x00700000
update_kernel=protect off a0080000 a077ffff ;erase a0080000 a077ffff ;cp.b 0x80000000 0xa0080000 0x00700000 ;protect on a0080000 a077ffff
rootfs_base=0xa0800000
rootfs_sec=a0800000 a1ffffff
menucmd=update
tftp_kernel_name_spark=mImage
tftp_kernel_name_enigma2=uImage
tftp_userfs_name_spark=userfsub.img
tftp_userfs_name_enigma2=e2jffs2.img
kernel_name_spark=spark/mImage
kernel_name_enigma2=enigma2/uImage
userfs_name_spark=spark/userfsub.img
userfs_name_enigma2=enigma2/e2jffs2.img
userfs_base_spark=800000
userfs_base_enigma2=18800000
userfs_len_spark=17800000
userfs_len_enigma2=7700000
kernelnfspath=192.168.40.19:/opt/target
rootfs_name=UserFS
rootfsnfspath=192.168.40.19:/home/d22cj/workspace/target
uboot_name=u-boot.bin
ubootnfspath=192.168.40.19:/home/d22cj/workspace/target
bootfromnfs=nfs a4000000 $kernelnfspath/$kernel_name;bootm a4000000
bootargs_nfs=console=ttyAS0,115200 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:61 stmmaceth=msglvl:0,phyaddr:1:watchdog:5000 root=/dev/nfs nfsroot=192.168.40.19:/opt/target,nfsvers=2,rsize=4096,wsize=8192,tcp rw ip=192.168.40.61:192.168.40.19:192.168.3.1:255.255.0.0:LINUX7109:eth0:off bigphysarea=4000
bootargs_flash=console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0:off stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000
bootargs_spark=console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0:off stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000
bootargs_enigma2=console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:61 rw ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:LINUX7109:eth0:off bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:2,watchdog:5000
magic_version=1.7
bootargs=console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:61 rw ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:LINUX7109:eth0:off bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:2,watchdog:5000
kernel_base=0x18000000
kernel_name=enigma2/uImage
userfs_name=enigma2/e2jffs2.img
tftp_kernel_name=uImage
tftp_userfs_name=e2jffs2.img
userfs_len=7700000
userfs_base=18800000
boot_system=enigma2
bootcmd=nboot.i 80000000 0 18000000;bootm 80000000
filesize=3EA0000
fuseburned=true
stdin=serial
stdout=serial
stderr=serial

Vielleicht wird ja daraus jemand schlauer.

HI, keiner mehr eine Idee??

Ne keine Idee.

Dein Bootloader war jedenfalls völlig ok. Dein Image verhält sich auch beim laden nicht ungewöhnlich.

Das es beim ersten Start bei 49% stehen bleibt ist "normal". Machen alle Images aus dem oe-git so. Wenn du dein System dann eingerichtet hast würde es von den Zahlen her durchlaufen.
Ein erster Bootvorgang dauert etwas über 2min.

Die Frage ist nun....rennt dein System wirklich nicht weiter durch? Oder ist es nicht weiter konfiguriert.
ftp-Zugang vorhanden?
Web-If an.

Erscheint ein Display-Spinner?
Blitzt das NFR-Logo sogar hier und da auf(Fernsehen).

Kann man aus der Ferne nicht beurteilen.

Grüße