Hallo und willkommen in unserer Community! Ist dies Dein erster Besuch?
Ergebnis 1 bis 2 von 2
  1. #1
    Anfänger

    Registriert seit
    24.08.2016
    Beiträge
    3
    DankeAktivitätenReceiverTagging

    RecoverAzboxKernel344 "Login incorrect"

    Hi Leute,

    ich habe ein technisch nicht erklärbares Problem mit meiner Azbox Premium+.
    Nach einem mißglückten Flash bleibt sie bei "Booting" stehen. OK, das ist kein Problem, dafür gibt es ja den YAMON und die serielle Konsole.
    So weit so gut, 1000 Mal nach Anleitung vorgegangen und 1000 Mal wurde das Login "root+azbox" abgewiesen. Und das nicht nur auf der
    seriellen Konsole sondern auch beim Versuch, eine FTP-Verbindung herzustellen:
    putty:
    Code:
    YAMON> load -b tftp://192.168.0.119/vmlinux.bin 0x90020000
    About to load tftp://192.168.0.119/vmlinux.bin
    Press Ctrl-C to break
    ................................................................
    ................................................................
    ................................................................
    ................................................................
    .......................................
    
    Start = 0x90020000, range = (0x90020000,0x9095880f), format = BINARY
    Length = 0x938810 (9668624)
    Checksum = 0x2254194d
    
    YAMON> go
    em86xx_eth ethernet stop
    Linux version 2.6.22.19-19-the_ripper (root@debian) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #185 PREEMPT Mon May 31 16:44:40 CEST 2010
    Configured for SMP863x (revision ES6+/RevA+), detected SMP8634 (revision ES9/RevC).
    Detected CPU/System/DSP Frequencies: 300.37/200.25/300.37MHz
    SMP86xx Enabled Devices under Linux/XENV 0x48000000 = 0x00021ace
     BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
    Valid MEMCFG found at 0x10000fc0.
    CPU revision is: 00019069
    Determined physical RAM map:
     memory: 06be0000 @ 10020000 (usable)
    User-defined physical RAM map:
     memory: 06ae0000 @ 10020000 (usable)
    Wasting 2098176 bytes for tracking 65568 unused pages
    Initrd not found or empty - disabling initrd
    On node 0 totalpages: 92928
      DMA zone: 726 pages used for memmap
      DMA zone: 0 pages reserved
      DMA zone: 92202 pages, LIFO batch:31
      Normal zone: 0 pages used for memmap
    Built 1 zonelists.  Total pages: 92202
    Kernel command line: mem=107m console=ttyS0,115200
    Primary instruction cache 16kB, 2-way, physically tagged, linesize 16 bytes.
    Primary data cache 16kB, 2-way, virtually tagged, cache aliases, linesize 16 bytes
    Synthesized TLB refill handler (20 instructions).
    Synthesized TLB load handler fastpath (32 instructions).
    Synthesized TLB store handler fastpath (32 instructions).
    Synthesized TLB modify handler fastpath (31 instructions).
    PID hash table entries: 2048 (order: 11, 8192 bytes)
    Using 150.188 MHz high precision timer.
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Memory: 96384k/109440k available (4018k kernel code, 12948k reserved, 1013k data, 4408k init, 0k highmem)
    Calibrating delay loop... 295.93 BogoMIPS (lpj=147968)
    Mount-cache hash table entries: 512
    NET: Registered protocol family 16
    tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x08000000.
    PCI: Initializing SMP86xx PCI host controller
    PCI: Remapped PCI I/O space 0x58000000 to 0xc8020000, size 64 kB
    PCI: Remapped PCI config space 0x50000000 to 0xc8004000, size 10 kB
    PCI: device 1 disabled
    PCI: device 4 disabled
    PCI: Configured SMP86xx as PCI slave with 128MB PCI memory
    PCI: Region size is 16384KB
    PCI: Map DMA memory 0x10020000-0x16b00000 for PCI at 0x11000000
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    Time: TANGOX clocksource has been installed.
    NET: Registered protocol family 2
    IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
    TCP: Hash tables configured (established 16384 bind 16384)
    TCP reno registered
    Created /proc/cpucache_info entry.
    Tango2 frequency scaling module installed.
    NTFS driver 2.1.28 [Flags: R/W DEBUG].
    JFFS2 version 2.2. © 2001-2006 Red Hat, Inc.
    fuse init (API version 7.8)
    SGI XFS with large block numbers, no debug enabled
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    Generic RTC Driver v1.07
    Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
    serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
    serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
    loop: module loaded
    nbd: registered device at major 43
    tango2_enet: ethernet driver for SMP863x internal mac
    tango2_enet: detected phy at address 0x01
    tango2_enet: mac address 00:02:14:18:36:74
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ide0: SMP86xx Bus Mastering IDE controller
    Probing IDE interface ide0...
    hda: TRANSCEND, ATA DISK drive
    hdb: SAMSUNG HD502HI, ATA DISK drive
    hda: selected mode 0x44
    hda: set to Ultra DMA mode 4
    ide0: DMA enabled for ATA DISK hda
    hdb: selected mode 0x45
    hdb: set to Ultra DMA mode 5
    ide0: DMA enabled for ATA DISK hdb
    ide0 at 0x223c0-0x223c7,0x22398 on irq 26
    hda: max request size: 128KiB
    hda: 3985632 sectors (2040 MB) w/2KiB Cache, CHS=3954/16/63, UDMA(66)
     hda: hda1 hda2 hda3 hda4 < hda5 >
    hdb: max request size: 128KiB
    hdb: 976773168 sectors (500107 MB) w/16384KiB Cache, CHS=60801/255/63, UDMA(100)
    hdb: cache flushes supported
     hdb: hdb1
    QLogic Fibre Channel HBA Driver
    physmap flash device CS2: 0x800000 at 0x48000000
    CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
     Amd/Fujitsu Extended Query Table at 0x0040
    number of CFI chips: 1
    cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
    Using physmap partition definition
    Adding partition #1-#5
    Creating 5 MTD partitions on "CS2: Physically mapped flash":
    0x00000000-0x00020000 : "CS2-Part1"
    0x00020000-0x00040000 : "CS2-Part2"
    0x00040000-0x00080000 : "CS2-Part3"
    0x00080000-0x00700000 : "CS2-Part4"
    0x00700000-0x00800000 : "CS2-Part5"
    PCI: Enabling device 0000:00:02.2 (0000 -> 0002)
    ehci_hcd 0000:00:02.2: EHCI Host Controller
    ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:02.2: irq 22, io mem 0x62008000
    ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 4 ports detected
    driver tangox-ehci-hcd, 10 Dec 2004
    TangoX USB initializing...
    tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
    tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 2
    tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021400
    tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    TCP cubic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Freeing unused kernel memory: 4408k freed
    Algorithmics/MIPS FPU Emulator v1.5
    Initializing random number generator... done.
    Starting network...
    ip: RTNETLINK answers: File exists
    eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
    udhcpc (v1.16.1) started
    Sending discover...
    Sending discover...
    Sending select for 192.168.0.114...
    Lease of 192.168.0.114 obtained, lease time 864000
    deleting routers
    route: SIOCDELRT: No such process
    adding dns 192.168.0.128
    ===> Starting services...
    [TD210] INITIALIZED END
    [TD210] SLEEP MODE OFF
    HDD Detected
    SCART Detected
    Micom Project PAVO
    ===> [1] telnetd starting...
    ===> [2] mounting DOM ...
    kjournald starting.  Commit interval 5 seconds
    EXT3 FS on hda1, internal journal
    EXT3-fs: recovery complete.
    EXT3-fs: mounted filesystem with ordered data mode.
    mount: mounting /dev/hda2 on /PLUGINS failed: Invalid argument
    mount: mounting /dev/hda3 on /DISK2 failed: Invalid argument
    attempt to access beyond end of device
    hda4: rw=0, want=4, limit=2
    EXT3-fs: unable to read superblock
    mount: mounting /dev/hda4 on /Download failed: Invalid argument
    insmod: can't read '/MMP/modules/2.6.22/llad.ko': No such file or directory
    insmod: can't read '/MMP/modules/2.6.22/em8xxx.ko': No such file or directory
    ===> Starting vsftpd...
    
    AZBOX login: root
    Password: azbox
    Login incorrect


    FTP-Client:
    Code:
    18:32:04 > Connecting...
    18:32:04 > Login...
    18:32:05 > Login incorrect - Username : root / Password : azbox
    Ich habe neben dem Archiv von hier einen Haufen Rettungspakete von diversen ULCs erfolglos probiert.
    Das Problem, die vmlinux.bin hat in allen Paketen die gleiche Größe von 9.668.624 Bytes und die
    Checksumme 03246E50. Es ist also überall die gleiche drin. Also keine Chance, mal eine andere auszu-
    probieren.
    Bisher habe ich eigentlich jede Box wiederbeleben können, aber hier bin ich jetzt ratlos. Was kann dazu
    führen, daß das Login, welches ja augenscheinlich bei hunderten anderen funktionierte, nun ausgerechnet
    bei mir sowohl seriell als auch über LAN schiefläuft?

    •   Alt Advertising

       

  2. #2
    Anfänger
    Themenstarter

    Registriert seit
    24.08.2016
    Beiträge
    3
    DankeAktivitätenReceiverTagging
    Vielen Dank für die zahlreiche Unterstützung. Ich habe die Box jetzt entsorgt. Schade drum.


 

Ähnliche Themen

  1. Slider FB für Zappix HD+ und Probleme mit Tasten "4", "5"& "7"
    Von Rusty70 im Forum Smart CX10 / VX10 / Zappix HD+
    Antworten: 3
    Letzter Beitrag: 16.06.2014, 17:50

Stichworte

Lesezeichen

Berechtigungen

  • Neue Themen erstellen: Nein
  • Themen beantworten: Nein
  • Anhänge hochladen: Nein
  • Beiträge bearbeiten: Nein
  •  
 Nachtfalke Reloaded Aktuell betrachtest Du unsere Community als Gast und hast somit nur begrenzten Zugriff auf Diskussionen, Bereiche und Downloads.
Registriere dich noch heute um auf alle Bereiche zuzugreifen!