Thema: DM900 startet nicht

Hej ,

meine DM 900 startet nicht leuchtet nur rot.
Konnte sie jetzt mit putty auslesen. Aber was jetzt - kann damit nichts anfagen.

Das hier ist der Log:
Ich hoffe ihr könnt mir helfen...

DANKE

PV=00000363(867)
MV=000003ab(939)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE... DONE
MICH: disable success
SSBL
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss 07080cd0
_ebss 0713dd70
_end 0713dd90
HEAP @ 07200000
STACK @ 09300000
ARCH: CONFIG OK
CLR BSS 07080cd0 to 0713dd70 OK
CLR SRAM OK
CACHE FLUSH OK
CPU CLKSET OK
GO!

,/
,'/___, BOLT v1.18 v1.18 LOCAL BUILD
.'__ ,' (2017-03-07 20:27:59 cynric@cynric-VirtualBox)
/,' Copyright (C) 2017 Broadcom
/'

Board: BCM97252SSFF
SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovi sion_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
CPU: 2x B15 [420f00f3] 1719 MHz
SCB: 432 MHz
DDR0 @ 1067MHz, DDR1 @ 1067MHz
RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
CS1: NAND: unrecognized ID: 0x32ffff 0xffffffff das hier ist mit roter Schrift
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 5
card if inited
set pwm to 0/255
disp id 5420
load image
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.936V, T=+59.400C, PV=0.867V, MV=0.939V, FW=30333278 [0.3.2.x]
USB otp=00000040
USB @ 0xf0470200: IPP is active low, IOC is negative polarity
init fp
found card in unknown state
ca valid!
set pwm to 200/255
Normal bootup
Loader:zimg Filesys:raw Dev:emmcflash0.kernel File: Optionsnull)
Reading 4249512 bytes from zImage...........
Starting program at 0x8000 (DTB @ 0x7728000)

32 bit boot...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.14-1.17-dm900 (newnigma2@nn2build2) (gcc version 5.3.0 (GCC) ) #1 SMP Mon Oct 30 17:37:52 CET 2017
[ 0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c7387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine model: BCM97252SSFF
[ 0.000000] moving dtb from 0x0000000007728000 to 0x0000000000839e70
[ 0.000000] bmem: Reserved 640 MiB at 0x0000000018000000
[ 0.000000] bmem: Reserved 384 MiB at 0x0000000080000000
[ 0.000000] cma: Reserved 16 MiB at 0x000000000f000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] MCP: Enabling write pairing
[ 0.000000] PERCPU: Embedded 8 pages/cpu @cdfc0000 s8384 r8192 d16192 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 523776
[ 0.000000] Kernel command line: bmem=640M@384M bmem=384M@2048M console=ttyS0 ,1000000 root=/dev/mmcblk0p2 rootwait rootfstype=ext4 coherent_pool=2M
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 1006896K/2097152K available (6114K kernel code, 214K rwda ta, 1600K rodata, 244K init, 208K bss, 1073872K reserved, 16384K cma-reserved, 7 86428K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0790cec (7716 kB)
[ 0.000000] .init : 0xc0791000 - 0xc07ce0c0 ( 245 kB)
[ 0.000000] .data : 0xc07d0000 - 0xc0805b20 ( 215 kB)
[ 0.000000] .bss : 0xc0805b28 - 0xc0839e70 ( 209 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 93)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 95)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 58)
[ 0.000000] Architected cp15 timer(s) running at 27.00MHz (virt).
[ 0.000005] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 25451 65795328ns
[ 0.000010] Switching to timer-based delay loop
[ 0.000235] Console: colour dummy device 80x30
[ 0.000254] Calibrating delay loop (skipped), value calculated using timer fr equency.. 54.00 BogoMIPS (lpj=27000)
[ 0.000263] pid_max: default: 32768 minimum: 301
[ 0.000355] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000360] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.005793] Initializing cgroup subsys devices
[ 0.005807] Initializing cgroup subsys freezer
[ 0.005814] Initializing cgroup subsys net_cls
[ 0.005840] CPU: Testing write buffer coherency: ok
[ 0.006061] CPU0: update cpu_power 1024
[ 0.006068] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.006116] Setting up static identity map for 0x5d5ab8 - 0x5d5b10
[ 0.007327] CPU1: Booted secondary processor
[ 0.007345] CPU1: update cpu_power 1024
[ 0.007348] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.007418] Brought up 2 CPUs
[ 0.007429] SMP: Total of 2 processors activated (108.00 BogoMIPS).
[ 0.007433] CPU: All CPU(s) started in SVC mode.
[ 0.007820] devtmpfs: initialized
[ 0.011428] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
[ 0.011980] regulator-dummy: no parameters
[ 0.012176] NET: Registered protocol family 16
[ 0.013120] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.013313] cpuidle: using governor ladder
[ 0.013318] cpuidle: using governor menu
[ 0.014464] irq: no irq domain found for /rdb/interrupt-controller@f040a700 !
[ 0.014548] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
[ 0.016237] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf0404523] regist ered
[ 0.016310] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] regist ered
[ 0.016377] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] regist ered
[ 0.016441] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] regist ered
[ 0.016504] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] regist ered
[ 0.016571] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] regist ered
[ 0.016637] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] regist ered
[ 0.016699] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] regist ered
[ 0.016761] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] regist ered
[ 0.016830] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] regist ered
[ 0.016898] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] regist ered
[ 0.016964] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] regist ered
[ 0.017028] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] regist ered
[ 0.017107] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] regist ered
[ 0.017415] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
[ 0.017642] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478
[ 0.021967] bio: create slab <bio-0> at 0
[ 0.022278] brcmstb-gpio f040a600.gpio: Couldn't get IRQ. Enable CONFIG_BCM71 20_L2_IRQ if you want GPIO interrupt support
[ 0.022303] brcmstb-gpio f040a600.gpio: Registered 5 banks (GPIO(s): 0-159)
[ 0.022333] brcmstb-gpio f0417400.gpio: Couldn't get IRQ. Enable CONFIG_BCM71 20_L2_IRQ if you want GPIO interrupt support
[ 0.022346] brcmstb-gpio f0417400.gpio: Registered 2 banks (GPIO(s): 160-223)
[ 0.022694] SCSI subsystem initialized
[ 0.022911] usbcore: registered new interface driver usbfs
[ 0.022942] usbcore: registered new interface driver hub
[ 0.023000] usbcore: registered new device driver usb
[ 0.023019] media: Linux media interface: v0.10
[ 0.023045] Linux video capture interface: v2.00
[ 0.023080] pps_core: LinuxPPS API ver. 1 registered
[ 0.023084] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it>
[ 0.023094] PTP clock support registered
[ 0.023327] Advanced Linux Sound Architecture Driver Initialized.
[ 0.023612] Bluetooth: Core ver 2.18
[ 0.023627] NET: Registered protocol family 31
[ 0.023630] Bluetooth: HCI device and connection manager initialized
[ 0.023640] Bluetooth: HCI socket layer initialized
[ 0.023646] Bluetooth: L2CAP socket layer initialized
[ 0.023653] Bluetooth: SCO socket layer initialized
[ 0.024048] Switched to clocksource arch_sys_counter
[ 0.024059] cfg80211: Calling CRDA to update world regulatory domain
[ 0.028420] thermal thermal_zone0: failed to read out thermal zone 0
[ 0.028508] NET: Registered protocol family 2
[ 0.028911] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.028927] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.028949] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.028983] TCP: reno registered
[ 0.028990] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.029002] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.029134] NET: Registered protocol family 1
[ 0.029366] RPC: Registered named UNIX socket transport module.
[ 0.029371] RPC: Registered udp transport module.
[ 0.029375] RPC: Registered tcp transport module.
[ 0.029378] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.029980] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.030330] bounce pool size: 64 pages
[ 0.030859] NFS: Registering the id_resolver key type
[ 0.030897] Key type id_resolver registered
[ 0.030902] Key type id_legacy registered
[ 0.030913] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.031035] SGI XFS with ACLs, security attributes, realtime, large block/ino de numbers, no debug enabled
[ 0.031348] msgmni has been set to 462
[ 0.032111] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 51)
[ 0.032119] io scheduler noop registered
[ 0.032137] io scheduler cfq registered (default)
[ 0.032358] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 258, 259
[ 0.032636] brcm-usb-phy f0470200.usb-phy: USB3.0 clock not found in Device T ree
[ 0.098327] brcmstb_memc f1102000.memc-ddr: registered
[ 0.098355] brcmstb_memc f1182000.memc-ddr: registered
[ 0.098539] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.099321] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A
[ 0.196023] console [ttyS0] enabled
[ 0.197259] loop: module loaded
[ 0.197904] ahci brcmstb-ahci.0: can't get clock
[ 0.198522] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
[ 0.210067] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 i mpl platform mode
[ 0.211063] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum p art
[ 0.213696] scsi0 : ahci_platform
[ 0.214325] scsi1 : ahci_platform
[ 0.214829] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x1 00 irq 91
[ 0.215754] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x1 80 irq 91
[ 0.217121] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address
[ 0.217893] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated
[ 0.219189] m25p80 spi32766.0: found mx25l25635e, expected m25p80
[ 0.219901] spi_brcmstb f03e3400.spi: 1-lane output, 4-byte address
[ 0.220634] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
[ 0.221281] 5 ofpart partitions found on MTD device spi32766.0
[ 0.221951] Creating 5 MTD partitions on "spi32766.0":
[ 0.222550] 0x000000000000-0x000000200000 : "flash0.bolt"
[ 0.223671] 0x000000200000-0x000000220000 : "flash0.nvram"
[ 0.224720] 0x000000220000-0x000000240000 : "flash0.devtree"
[ 0.225789] 0x000000240000-0x000001000000 : "flash0.recovery"
[ 0.226852] 0x000000000000-0x000002000000 : "flash0"
[ 0.228135] libphy: Fixed MDIO Bus: probed
[ 0.228725] tun: Universal TUN/TAP device driver, 1.6
[ 0.229314] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.230362] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
[ 0.244053] libphy: bcmgenet MII bus: probed
[ 0.264935] xhci-brcm: xHCI BRCM driver
[ 0.265456] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[ 0.266128] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
[ 0.267318] xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000
[ 0.268169] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.268949] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 0.269785] usb usb1: Product: xHCI Host Controller
[ 0.270352] usb usb1: Manufacturer: Linux 3.14-1.17-dm900 xhci-hcd
[ 0.271073] usb usb1: SerialNumber: f0471000.xhci_v2
[ 0.271963] hub 1-0:1.0: USB hub found
[ 0.272425] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 0.273358] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[ 0.274014] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
[ 0.275046] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.275825] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 0.276659] usb usb2: Product: xHCI Host Controller
[ 0.277232] usb usb2: Manufacturer: Linux 3.14-1.17-dm900 xhci-hcd
[ 0.277941] usb usb2: SerialNumber: f0471000.xhci_v2
[ 0.278793] hub 2-0:1.0: USB hub found
[ 0.279253] hub 2-0:1.0: 2 ports detected
[ 0.280026] ehci-brcm: EHCI BRCM driver
[ 0.280552] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
[ 0.281224] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
[ 0.292233] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300
[ 0.298057] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
[ 0.298871] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.299660] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 0.300495] usb usb3: Product: EHCI Host Controller
[ 0.301062] usb usb3: Manufacturer: Linux 3.14-1.17-dm900 ehci_hcd
[ 0.301771] usb usb3: SerialNumber: f0470300.ehci_v2
[ 0.302609] hub 3-0:1.0: USB hub found
[ 0.303070] hub 3-0:1.0: 1 port detected
[ 0.303720] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
[ 0.304388] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
[ 0.315384] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500
[ 0.322055] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
[ 0.322859] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.323647] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 0.324481] usb usb4: Product: EHCI Host Controller
[ 0.325048] usb usb4: Manufacturer: Linux 3.14-1.17-dm900 ehci_hcd
[ 0.325756] usb usb4: SerialNumber: f0470500.ehci_v2
[ 0.326590] hub 4-0:1.0: USB hub found
[ 0.327051] hub 4-0:1.0: 1 port detected
[ 0.327738] ohci-brcm: OHCI BRCM driver
[ 0.328247] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
[ 0.328909] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5
[ 0.329062] ata1: SATA link down (SStatus 0 SControl 300)
[ 0.330449] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400
[ 0.386175] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.386955] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 0.387791] usb usb5: Product: BRCM OHCI controller
[ 0.388358] usb usb5: Manufacturer: Linux 3.14-1.17-dm900 ohci_hcd
[ 0.389073] usb usb5: SerialNumber: f0470400.ohci_v2
[ 0.389927] hub 5-0:1.0: USB hub found
[ 0.390399] hub 5-0:1.0: 1 port detected
[ 0.391061] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
[ 0.391723] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6
[ 0.392648] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600
[ 0.441056] ata2: SATA link down (SStatus 0 SControl 300)
[ 0.448156] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.448936] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 0.449771] usb usb6: Product: BRCM OHCI controller
[ 0.450338] usb usb6: Manufacturer: Linux 3.14-1.17-dm900 ohci_hcd
[ 0.451054] usb usb6: SerialNumber: f0470600.ohci_v2
[ 0.451878] hub 6-0:1.0: USB hub found
[ 0.452349] hub 6-0:1.0: 1 port detected
[ 0.453060] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.453809] ehci-pci: EHCI PCI platform driver
[ 0.454364] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.455084] ohci-pci: OHCI PCI platform driver
[ 0.455707] usbcore: registered new interface driver usb-storage
[ 0.456409] i2c /dev entries driver
[ 0.456857] lirc_dev: IR Remote Control driver registered, major 250
[ 0.457911] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor d river
[ 0.458894] usbcore: registered new interface driver btusb
[ 0.459589] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 0.460403] brcmstb-cpufreq: probe of f03e257c.cpu-clk-div failed with error -17
[ 0.461337] sdhci: Secure Digital Host Controller Interface driver
[ 0.462053] sdhci: Copyright(c) Pierre Ossman
[ 0.462553] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.464305] mmc0: no vqmmc regulator found
[ 0.464779] mmc0: no vmmc regulator found
[ 0.495057] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using A DMA
[ 0.496965] mmc1: no vqmmc regulator found
[ 0.497444] mmc1: no vmmc regulator found
[ 0.528052] mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using A DMA
[ 0.528992] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.529701] usbcore: registered new interface driver usbhid
[ 0.530349] usbhid: USB HID core driver
[ 0.532788] TCP: cubic registered
[ 0.533787] NET: Registered protocol family 10
[ 0.534760] NET: Registered protocol family 17
[ 0.535492] Bluetooth: RFCOMM TTY layer initialized
[ 0.536078] Bluetooth: RFCOMM socket layer initialized
[ 0.536670] Bluetooth: RFCOMM ver 1.11
[ 0.537110] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 0.537720] Bluetooth: BNEP filters: protocol multicast
[ 0.538328] Bluetooth: BNEP socket layer initialized
[ 0.538899] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.539588] Bluetooth: HIDP socket layer initialized
[ 0.540207] l2tp_core: L2TP core driver, V2.0
[ 0.540729] Key type dns_resolver registered
[ 0.541298] Registering SWP/SWPB emulation handler
[ 0.542119] regulator-dummy: disabling
[ 0.544798] ALSA device list:
[ 0.545153] No soundcards found.
[ 0.545763] Waiting for root device /dev/mmcblk0p2...
[ 0.597696] mmc1: BKOPS_EN bit is not set
[ 0.604395] mmc1: new high speed MMC card at address 0001
[ 0.605218] mmcblk0: mmc1:0001 4FPD3R 3.64 GiB
[ 0.605831] mmcblk0boot0: mmc1:0001 4FPD3R partition 1 4.00 MiB
[ 0.606613] mmcblk0boot1: mmc1:0001 4FPD3R partition 2 4.00 MiB
[ 0.607379] mmcblk0rpmb: mmc1:0001 4FPD3R partition 3 512 KiB
[ 0.611573] mmcblk0: p1 p2 p3
[ 0.614521] mmcblk0boot1: unknown partition table
[ 0.615569] mmcblk0boot0: unknown partition table
[ 0.649646] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. O pts: (null)
[ 0.650605] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 0.652226] devtmpfs: error mounting -2
[ 0.652718] Kernel panic - not syncing: No working init found. Try passing i nit= option to kernel. See Linux Documentation/init.txt for guidance.
[ 0.654221] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.14-1.17-dm900 #1
[ 0.655010] [<c0014eb0>] (unwind_backtrace) from [<c00112f0>] (show_stack+0x1 0/0x14)
[ 0.655903] [<c00112f0>] (show_stack) from [<c05d0408>] (dump_stack+0x88/0x9c )
[ 0.656734] [<c05d0408>] (dump_stack) from [<c05cf770>] (panic+0xa0/0x1f0)
[ 0.657525] [<c05cf770>] (panic) from [<c05cd564>] (cpu_die+0x0/0x90)
[ 0.658266] [<c05cd564>] (cpu_die) from [<00000000>] ( (null))
[ 0.658950] CPU0: stopping
[ 0.659266] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14-1.17-dm900 #1
[ 0.660041] [<c0014eb0>] (unwind_backtrace) from [<c00112f0>] (show_stack+0x1 0/0x14)
[ 0.660932] [<c00112f0>] (show_stack) from [<c05d0408>] (dump_stack+0x88/0x9c )
[ 0.661763] [<c05d0408>] (dump_stack) from [<c00140d4>] (handle_IPI+0x164/0x1 98)
[ 0.662612] [<c00140d4>] (handle_IPI) from [<c00085cc>] (gic_handle_irq+0x58/ 0x5c)
[ 0.663483] [<c00085cc>] (gic_handle_irq) from [<c0011dc0>] (__irq_svc+0x40/0 x50)
[ 0.664339] Exception stack(0xc07d1f60 to 0xc07d1fa8)
[ 0.664922] 1f60: ffffffed 0d7f4000 c07d94c8 00000000 c07d0030 c07d8420 c07d8 49c c05d788c
[ 0.665859] 1f80: c0805961 c0805961 c07d0000 00000000 00000000 c07d1fa8 c000e fb0 c000efa8
[ 0.666794] 1fa0: 60000113 ffffffff
[ 0.667201] [<c0011dc0>] (__irq_svc) from [<c000efa8>] (arch_cpu_idle+0x2c/0x 38)
[ 0.668053] [<c000efa8>] (arch_cpu_idle) from [<c00638f8>] (cpu_startup_entry +0x100/0x144)
[ 0.669006] [<c00638f8>] (cpu_startup_entry) from [<c0791bf0>] (start_kernel+ 0x414/0x420)

Angebot von mir.

Sende Sie mir zu.Ich bringe Sie wieder zum laufen.Habe schon mehrere mit roter LED wieder ins Leben geholt.

wohin? und was kostet das? und kommt meine Box wieder zurück?
Ich bin im Rhein Main Gebiet
Ich möchte sie einfach wieder flashen, aber komm ja nicht an die Box ran

Hab Dir eine PN gesendet.

Noch ein Tipp:

Schliesse das Antennenkabel am anderen Tuner an und schaue, ob sie dann startet.

habe gleiche problem

Du hast Post.